Nice Sterling Silver Rectangle Wire,Hollow Rubber Tube, and Turquoise Earrings(jewelry tutorial)




Sterling Silver Crescent and Bead Earrings

Products Wanted
three" 4 x 1 mm sterling silver rectangle wire
Twenty-one particular 'Λ* head pins
Two turquoise disc beads
Just one Vi* one.7 mm black hollow rubber tube
Two sterling silver ear wires
What guidance would you give you a starting artist?
“Do Anything you love. Discover distinct media. Offer with a selective, limited, basis in the beginning to view what will work or what would not be just right for you before you jump into A significant outlay of money and effort.*
-Sally J. Phillips Jewelry Designer
Equipment Wanted
Ruler
Marker
Jeweler's observed or tin snips Protection Eyeglasses Hard, flat surface Awl
Hammer /is" drill bit
Hand held rotary Instrument, flex shaft, or drill press File
Fantastic grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Round nose pliers


1.Make use of the ruler to evaluate and mark two one Vi’ items of four x one mm rectangle sterling silver wire.
2Using a jeweler's noticed or tin snips, Minimize the four x one mm rectangle sterling silver wire into two one Vi’ lengths.
three.File Just about every close of your 1Vi" rectangle wire parts to remove any burs or tough edges.
If desired, you can use the file to round the ends from the rectangle wire pieces. Use a good grit sanding pad to go more than the realm where you have filed to smooth the edges and remove any file marks.
4.Use the ruler to evaluate and mark /*." from a person end of the one Vi’ parts of rectangle wire and put a mark in the middle of your wire. This is when you might drill the holes to slip The pinnacle pins by.
five.Place with your security glasses!!! Location the 1 Vi" rectangle wire pieces onto a tough, flat area. Put The purpose with the awl to the mark you designed Vm,' from just one conclude on the rectangle wire items, and firmly strike when on the very best from the awl using a hammer. This will make a pilot hole for drilling holes into the rectangle wire.

Sterling Silver Crescent and Bead Earrings
Chapter five

six.Utilizing Mens Ring a /is" drill bit. drill holes into a single finish from the rectangle wire pieces which has a handheld rotary Software, flex shaft, or drill push (even though nevertheless mens ring sporting your safety glasses!).
seven.Utilize the file or wonderful grit sanding pad to eradicate any burs Mens Ring or rough edges left from drilling holes into your rectangle wire parts.
eight.Curve the two 1W pieces of rectangle wire into a “C" condition employing a ring mandrel and rawhide mallet. If you do not have a ring mandrel and rawhide mallet, use two pair of chain nose pliers. Keeping just one pair of pliers in Every hand, grasp Every end of your one Vi* rectangle wire piece With all the pliers and gently bend the rectangle wire into a “C* condition. Assess the two from the C-shaped rectangle wire parts and alter the curves so that they are similar in si2e. Established these apart.
9.Use the ruler to evaluate and mark the rubber tube into 4 equal parts measuring Vm’ Just about every. Use scissors to chop the rubber tube.
10.Place the turquoise disc bead on to The top pin and include one V·' bit of the rubber tube, spot the head pin in the gap inside the C-shaped rectangle wire, after which you can insert another V«" piece of rubber tube.

thirteen. Maintain the head pin While using the bead, rubber tube, plus the rectangle wire on it in one hand with the wire that you choose to bent pointing towards you. Using the spherical nose pliers, grip the tip of the head pin wire that is pointing towards you and roll it far from you (think of turning the ignition critical to begin your car). Launch the pliers from The top pin wire.
At this point, the opening from the loop at the very best of the head pin wire really should nevertheless be large plenty of to slip the ear wire on. After you insert the ear wire, use the spherical nose pliers to grasp the loop of The top pin Mens Ring wire and roll it closed. You should utilize the round nose or chain nose pliers to regulate The form from the loop at the best of The top pin if you need to.
eleven. Use the ruler to evaluate and mark /(.’ previously mentioned the top bit of the hollow rubber tube. Using the wire cutters or tin snips, Slice The top pin wire Yu.’ higher than the highest from the hollow rubber tube.
twelve. Make use of the chain nose pliers to bend The pinnacle pin wire close to the top with the rubber tube at a ninety-degree angle.
fourteen. Repeat these measures for the mens ring 2nd earring.







Leave a Reply

Your email address will not be published. Required fields are marked *